View IRFR4620PBF_4953977.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PD -96207A
IRFR4620PBF IRFU4620PbF
HEXFET(R) Power MOSFET
Applications l High Efficiency Synchronous Rectification in SMPS l Uninterruptible Power Supply l High Speed Power Switching l Hard Switched and High Frequency Circuits Benefits l Improved Gate, Avalanche and Dynamic dV/dt Ruggedness l Fully Characterized Capacitance and Avalanche SOA l Enhanced body diode dV/dt and dI/dt Capability l Lead-Free
D G S
VDSS RDS(on) typ. max. ID
D D
200V 64m: 78m: 24A
S G
G
D
S
DPak IRFR4620PBF G D
IPAK IRFU4620PbF S
Gate
Drain
Source
Absolute Maximum Ratings
Symbol
ID @ TC = 25C ID @ TC = 100C IDM PD @TC = 25C VGS dv/dt TJ TSTG
Parameter
Continuous Drain Current, VGS @ 10V Continuous Drain Current, VGS @ 10V Pulsed Drain Current Maximum Power Dissipation Linear Derating Factor Gate-to-Source Voltage Peak Diode Recovery Operating Junction and Storage Temperature Range Soldering Temperature, for 10 seconds (1.6mm from case)
Max.
24 17 100 144 0.96 20 54 -55 to + 175 300
Units
A W W/C V V/ns
c
e
C
Avalanche Characteristics
EAS (Thermally limited) IAR EAR Single Pulse Avalanche Energy Avalanche Current Repetitive Avalanche Energy
c
d
c i
113 See Fig. 14, 15, 22a, 22b,
mJ A mJ
Thermal Resistance
Symbol
RJC RJA RJA Junction-to-Case Junction-to-Ambient (PCB Mount) Junction-to-Ambient
j
Parameter
Typ.
--- --- ---
Max.
1.045 50 110
Units
C/W
ORDERING INFORMATION: See detailed ordering and shipping information on the last page of this data sheet.
Notes through are on page 11
www.irf.com
1
06/08/09
IRFR/U4620PbF
Static @ TJ = 25C (unless otherwise specified)
Symbol
V(BR)DSS V(BR)DSS/TJ RDS(on) VGS(th) IDSS IGSS RG(int)
Parameter
Drain-to-Source Breakdown Voltage Breakdown Voltage Temp. Coefficient Static Drain-to-Source On-Resistance Gate Threshold Voltage Drain-to-Source Leakage Current Gate-to-Source Forward Leakage Gate-to-Source Reverse Leakage Internal Gate Resistance
Min. Typ. Max. Units
200 --- --- 3.0 --- --- --- ---
---
Conditions
--- 0.23 64 --- --- --- --- --- 2.6
--- V VGS = 0V, ID = 250A --- V/C Reference to 25C, ID = 5mA 78 m VGS = 10V, ID = 15A 5.0 V VDS = VGS, ID = 100A VDS = 200V, VGS = 0V 20 A 250 VDS = 200V, VGS = 0V, TJ = 125C 100 VGS = 20V nA VGS = -20V -100
f
---
Dynamic @ TJ = 25C (unless otherwise specified)
Symbol
gfs Qg Qgs Qgd Qsync td(on) tr td(off) tf Ciss Coss Crss Coss eff. (ER) Coss eff. (TR)
Parameter
Forward Transconductance Total Gate Charge Gate-to-Source Charge Gate-to-Drain ("Miller") Charge Total Gate Charge Sync. (Qg - Qgd) Turn-On Delay Time Rise Time Turn-Off Delay Time Fall Time Input Capacitance Output Capacitance Reverse Transfer Capacitance
Min. Typ. Max. Units
--- 25 8.2 7.9 17 13.4 22.4 25.4 14.8 1710 125 30 113 317 --- 38 --- --- --- --- --- --- --- --- --- --- --- --- S
Conditions
37 --- --- --- --- --- --- --- --- --- --- --- Effective Output Capacitance (Energy Related)hA --- --- Effective Output Capacitance (Time Related)g
VDS = 50V, ID = 15A ID = 15A VDS = 100V nC VGS = 10V ID = 15A, VDS =0V, VGS = 10V VDD = 130V ID = 15A ns RG = 7.3 VGS = 10V VGS = 0V VDS = 50V pF = 1.0MHz (See Fig.5) VGS = 0V, VDS = 0V to 160V VGS = 0V, VDS = 0V to 160V
f
f
h(See Fig.11) g
D
Diode Characteristics
Symbol
IS ISM VSD trr Qrr IRRM ton
Parameter
Continuous Source Current (Body Diode) Pulsed Source Current (Body Diode)A Diode Forward Voltage Reverse Recovery Time Reverse Recovery Charge Reverse Recovery Current Forward Turn-On Time
Min. Typ. Max. Units
--- --- --- --- 24 A 100
Conditions
MOSFET symbol showing the integral reverse
G S
--- --- 1.3 V --- 78 --- ns --- 99 --- --- 294 --- nC TJ = 125C --- 432 --- --- 7.6 --- A TJ = 25C Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD)
p-n junction diode. TJ = 25C, IS = 15A, VGS = 0V VR = 100V, TJ = 25C TJ = 125C IF = 15A di/dt = 100A/s TJ = 25C
f
f
2
www.irf.com
IRFR/U4620PbF
1000
TOP VGS 15V 12V 10V 8.0V 7.0V 6.0V 5.5V 5.0V
1000
TOP VGS 15V 12V 10V 8.0V 7.0V 6.0V 5.5V 5.0V
ID, Drain-to-Source Current (A)
ID, Drain-to-Source Current (A)
100
100
BOTTOM
10
BOTTOM
10
5.0V
1 5.0V 0.1 60s PULSE WIDTH Tj = 25C 0.01 0.1 1 10 100 V DS, Drain-to-Source Voltage (V)
1
60s PULSE WIDTH
Tj = 175C 0.1 0.1 1 10 100 V DS, Drain-to-Source Voltage (V)
Fig 1. Typical Output Characteristics
1000
RDS(on) , Drain-to-Source On Resistance (Normalized)
Fig 2. Typical Output Characteristics
3.5 3.0 2.5 2.0 1.5 1.0 0.5 ID = 15A VGS = 10V
ID, Drain-to-Source Current (A)
100
TJ = 175C T J = 25C
10
1 VDS = 50V 60s PULSE WIDTH 0.1 2 4 6 8 10 12 14 16
-60 -40 -20 0 20 40 60 80 100120140160180 T J , Junction Temperature (C)
VGS, Gate-to-Source Voltage (V)
Fig 3. Typical Transfer Characteristics
100000
VGS = 0V, f = 1 MHZ C iss = C gs + C gd, C ds SHORTED C rss = C gd C oss = C ds + C gd
Fig 4. Normalized On-Resistance vs. Temperature
14.0
VGS, Gate-to-Source Voltage (V)
12.0 10.0 8.0 6.0 4.0 2.0 0.0
ID= 15A
10000
C, Capacitance (pF)
VDS= 160V VDS= 100V VDS= 40V
1000
Ciss
Coss 100 Crss
10 1 10 100 1000 VDS, Drain-to-Source Voltage (V)
0
5
10
15
20
25
30
35
QG, Total Gate Charge (nC)
Fig 5. Typical Capacitance vs. Drain-to-Source Voltage
Fig 6. Typical Gate Charge vs. Gate-to-Source Voltage
www.irf.com
3
IRFR/U4620PbF
100
1000 OPERATION IN THIS AREA LIMITED BY R DS(on) 100
100sec 1msec
T J = 175C 10
T J = 25C
ID, Drain-to-Source Current (A)
ISD, Reverse Drain Current (A)
10
10msec
DC
1 Tc = 25C Tj = 175C Single Pulse 0.1 1 10 100 1000
VGS = 0V 1.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 VSD, Source-to-Drain Voltage (V)
Fig 7. Typical Source-Drain Diode Forward Voltage
30 25
ID, Drain Current (A)
Fig 8. Maximum Safe Operating Area
V(BR)DSS , Drain-to-Source Breakdown Voltage (V)
VDS, Drain-to-Source Voltage (V)
260 Id = 5mA 250 240 230 220 210 200 190 -60 -40 -20 0 20 40 60 80 100120140160180 T J , Temperature ( C )
20 15 10 5 0 25 50 75 100 125 150 175 T C , Case Temperature (C)
Fig 9. Maximum Drain Current vs. Case Temperature
3.0
Fig 10. Drain-to-Source Breakdown Voltage
500
EAS , Single Pulse Avalanche Energy (mJ)
2.5 2.0
450 400 350 300 250 200 150 100 50 0 25 50 75 100
ID TOP 2.05A 2.94A BOTTOM 15A
Energy (J)
1.5 1.0 0.5 0.0 -50 0 50 100 150 200
125
150
175
Fig 11. Typical COSS Stored Energy
VDS, Drain-to-Source Voltage (V)
Starting T J , Junction Temperature (C)
Fig 12. Maximum Avalanche Energy vs. DrainCurrent
4
www.irf.com
IRFR/U4620PbF
10
Thermal Response ( Z thJC ) C/W
1 D = 0.50 0.20 0.10 0.05 0.02 0.01 0.01 SINGLE PULSE ( THERMAL RESPONSE ) 1E-005 0.0001 0.001
0.1
J
R1 R1 J 1 2
R2 R2 C
Ri (C/W) 0.456 0.589
i (sec) 0.000311 0.003759
1
2
Ci= i/Ri Ci i/Ri
Notes: 1. Duty Factor D = t1/t2 2. Peak Tj = P dm x Zthjc + Tc 0.01 0.1
0.001 1E-006
t1 , Rectangular Pulse Duration (sec)
Fig 13. Maximum Effective Transient Thermal Impedance, Junction-to-Case
100
Duty Cycle = Single Pulse
Avalanche Current (A)
10
0.01
Allowed avalanche Current vs avalanche pulsewidth, tav, assuming Tj = 150C and Tstart =25C (Single Pulse)
0.05 0.10 1 Allowed avalanche Current vs avalanche pulsewidth, tav, assuming j = 25C and Tstart = 150C. 0.1 1.0E-06 1.0E-05 1.0E-04 tav (sec) 1.0E-03 1.0E-02 1.0E-01
Fig 14. Typical Avalanche Current vs.Pulsewidth
120 100 80 60 40 20 0 25 50 75 100 125 150 175 Starting T J , Junction Temperature (C) TOP Single Pulse BOTTOM 1.0% Duty Cycle ID = 15A
Notes on Repetitive Avalanche Curves , Figures 14, 15: (For further info, see AN-1005 at www.irf.com) 1. Avalanche failures assumption: Purely a thermal phenomenon and failure occurs at a temperature far in excess of Tjmax. This is validated for every part type. 2. Safe operation in Avalanche is allowed as long asTjmax is not exceeded. 3. Equation below based on circuit and waveforms shown in Figures 16a, 16b. 4. PD (ave) = Average power dissipation per single avalanche pulse. 5. BV = Rated breakdown voltage (1.3 factor accounts for voltage increase during avalanche). 6. Iav = Allowable avalanche current. 7. T = Allowable rise in junction temperature, not to exceed Tjmax (assumed as 25C in Figure 14, 15). tav = Average time in avalanche. D = Duty cycle in avalanche = tav *f ZthJC(D, tav) = Transient thermal resistance, see Figures 13) PD (ave) = 1/2 ( 1.3*BV*Iav) = DT/ ZthJC Iav = 2DT/ [1.3*BV*Zth] EAS (AR) = PD (ave)*tav
Fig 15. Maximum Avalanche Energy vs. Temperature
www.irf.com
EAR , Avalanche Energy (mJ)
5
IRFR/U4620PbF
6.0
VGS(th), Gate threshold Voltage (V)
90 80 70 60
IRRM (A)
5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 -75 -50 -25 0 25 50 75 100 125 150 175 T J , Temperature ( C ) ID = 100A ID = 250uA ID = 1.0mA ID = 1.0A
IF = 10A V R = 100V TJ = 25C TJ = 125C
50 40 30 20 10 0 0 200 400 600 800 1000 diF /dt (A/s)
Fig 16. Threshold Voltage vs. Temperature
90 80 70 60
IRRM (A)
Fig. 17 - Typical Recovery Current vs. dif/dt
2000
IF = 15A V R = 100V TJ = 25C TJ = 125C
1800 1600 1400
QRR (A)
IF = 10A V R = 100V TJ = 25C TJ = 125C
50 40 30 20 10 0 0 200 400 600 800 1000 diF /dt (A/s)
1200 1000 800 600 400 200 0 200 400 600 800 1000 diF /dt (A/s)
Fig. 18 - Typical Recovery Current vs. dif/dt
2000 1800 1600 1400
QRR (A)
Fig. 19 - Typical Stored Charge vs. dif/dt
IF = 15A V R = 100V TJ = 25C TJ = 125C
1200 1000 800 600 400 200 0 200 400 600 800 1000 diF /dt (A/s)
6
Fig. 20 - Typical Stored Charge vs. dif/dt
www.irf.com
IRFR/U4620PbF
D.U.T
Driver Gate Drive
+
P.W.
Period
D=
P.W. Period VGS=10V
+
Circuit Layout Considerations * Low Stray Inductance * Ground Plane * Low Leakage Inductance Current Transformer
*
D.U.T. ISD Waveform Reverse Recovery Current Body Diode Forward Current di/dt D.U.T. VDS Waveform Diode Recovery dv/dt
-
-
+
RG
* * * * dv/dt controlled by RG Driver same type as D.U.T. I SD controlled by Duty Factor "D" D.U.T. - Device Under Test
VDD
VDD
+ -
Re-Applied Voltage
Body Diode
Forward Drop
Inductor Curent Inductor Current
Ripple 5% ISD
* VGS = 5V for Logic Level Devices Fig 21. Peak Diode Recovery dv/dt Test Circuit for N-Channel HEXFET(R) Power MOSFETs
V(BR)DSS
15V
tp
DRIVER
VDS
L
RG
VGS 20V
D.U.T
IAS tp
+ V - DD
A
0.01
I AS
Fig 22a. Unclamped Inductive Test Circuit
VDS VGS RG RD
Fig 22b. Unclamped Inductive Waveforms
VDS 90%
D.U.T.
+
- VDD
V10V GS
Pulse Width 1 s Duty Factor 0.1 %
10% VGS
td(on) tr t d(off) tf
Fig 23a. Switching Time Test Circuit
Current Regulator Same Type as D.U.T.
Fig 23b. Switching Time Waveforms
Id Vds Vgs
50K 12V .2F .3F
D.U.T. VGS
3mA
+ V - DS
Vgs(th)
IG
ID
Current Sampling Resistors
Qgs1 Qgs2
Qgd
Qgodr
www.irf.com
Fig 24a. Gate Charge Test Circuit
Fig 24b. Gate Charge Waveform
7
IRFR/U4620PbF
D-Pak (TO-252AA) Package Outline
Dimensions are shown in millimeters (inches)
D-Pak (TO-252AA) Part Marking Information
@Y6HQG@) UCDTADTA6IADSAS XDUCA6TT@H7G GPUA8P9@A !"# %A! ! Q6SUAIVH7@S DIU@SI6UDPI6G S@8UDAD@S GPBP
6TT@H7G@9APIAXXA
DIAUC@A6TT@H7GAGDI@AA6A
,5)5 $
96U@A8P9@ @6SA X@@FA GDI@A6 A2A! %
Ir)AAQAAvAhriyAyvrAvv vqvphrAAGrhqArrA
6TT@H7G GPUA8P9@
AQAAvAhriyAyvrAvvAvqvphr AGrhqArrAAhyvsvphvAAurApryrry
25
Q6SUAIVH7@S DIU@SI6UDPI6G S@8UDAD@S GPBP
,5)5
96U@A8P9@ QA2A9@TDBI6U@TAG@69AS@@ QSP9V8UAPQUDPI6G QA2A9@TDBI6U@TAG@69AS@@ QSP9V8UARV6GDAD@9AUPAUC@ 8PITVH@SAG@W@GAPQUDPI6G
6TT@H7G GPUA8P9@
@6SA X@@FA
A2A! %
6A2A6TT@H7GATDU@A8P9@
Note: For the most current drawing please refer to IR website at http://www.irf.com/package/
8
www.irf.com
IRFR/U4620PbF
I-Pak (TO-251AA) Package Outline
Dimensions are shown in millimeters (inches)
I-Pak (TO-251AA) Part Marking Information
@Y6HQG@) UCDTADTA6IADSAV ! XDUCA6TT@H7G GPUA8P9@A$%&' 6TT@H7G@9APIAXXA (A! DIAUC@A6TT@H7GAGDI@AA6A Ir)AAQAAvAhriyAyvrAvv vqvphrAGrhqArrA DIU@SI6UDPI6G S@8UDAD@S GPBP 6TT@H7G GPUA8P9@ Q6SUAIVH7@S
,5)8 $
96U@A8P9@ @6SA A2A! X@@FA ( GDI@A6
25
DIU@SI6UDPI6G S@8UDAD@S GPBP 6TT@H7G GPUA8P9@ Q6SUAIVH7@S
,5)8
96U@A8P9@ QA2A9@TDBI6U@TAG@69AS@@ QSP9V8UAPQUDPI6G @6SA A2A! X@@FA ( 6A2A6TT@H7GATDU@A8P9@
Note: For the most current drawing please refer to IR website at http://www.irf.com/package/
www.irf.com
9
IRFR/U4620PbF
D-Pak (TO-252AA) Tape & Reel Information
Dimensions are shown in millimeters (inches)
TR
TRR
TRL
16.3 ( .641 ) 15.7 ( .619 )
16.3 ( .641 ) 15.7 ( .619 )
12.1 ( .476 ) 11.9 ( .469 )
FEED DIRECTION
8.1 ( .318 ) 7.9 ( .312 )
FEED DIRECTION
NOTES : 1. CONTROLLING DIMENSION : MILLIMETER. 2. ALL DIMENSIONS ARE SHOWN IN MILLIMETERS ( INCHES ). 3. OUTLINE CONFORMS TO EIA-481 & EIA-541.
13 INCH
16 mm NOTES : 1. OUTLINE CONFORMS TO EIA-481.
Note: For the most current drawing please refer to IR website at http://www.irf.com/package/
10
www.irf.com
IRFR/U4620PbF
Orderable part number IRFR4620PBF IRFR4620TRPbF IRFU4620PbF Qualification Information
Qualification level
Package Type D-PAK D-PAK I-PAK
Standard Pack Form Quantity Tube/Bulk 75 Tape and Reel 2000 Tube/Bulk 75
Note
Industrial

(per JEDEC JESD47F
guidelines)
Comments: This family of products has passed JEDEC's Industrial qualification. IR's Consumer qualification level is granted by extension of the higher Industrial level.
Moisture Sensitivity Level D-PAK I-PAK RoHS Compliant Yes MSL1 (per JEDEC J-STD-020D) Not applicable
Qualification standards can be found at International Rectifier's web site http://www.irf.com/product-info/reliability Higher qualification ratings may be available should the user have such requirements. Please contact your International Rectifier sales representative for further information: http://www.irf.com/whoto-call/salesrep/ Applicable version of JEDEC standard at the time of product release.
Notes: Repetitive rating; pulse width limited by max. junction temperature. Limited by TJmax, starting TJ = 25C, L = 1.0mH RG = 25, IAS = 15A, VGS =10V. Part not recommended for use above this value . ISD 15A, di/dt 634A/s, VDD V(BR)DSS, TJ 175C. Pulse width 400s; duty cycle 2%.
Coss eff. (TR) is a fixed capacitance that gives the same charging time
as Coss while VDS is rising from 0 to 80% VDSS.
Coss eff. (ER) is a fixed capacitance that gives the same energy as When mounted on 1" square PCB (FR-4 or G-10 Material). For recom R is measured at TJ approximately 90C
Coss while VDS is rising from 0 to 80% VDSS . mended footprint and soldering techniques refer to application note #AN-994.
Data and specifications subject to change without notice
www.irf.com
IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7903 Visit us at www.irf.com for sales contact information. 06/2009
11

▲Up To Search▲

Price & Availability of IRFR4620PBF

	To Download IRFR4620PBF Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .